We have uncovered this post relating to How to Install a Bathtub Yourself listed below on the web and believe it made perfect sense to discuss it with you in this article.
Mounting a tub isn't exactly brain surgery, however it does require solid plumbing, woodworking, and also often, tiling skills. Changing an old bath tub with a brand-new one is likewise a reasonably challenging job. If the old tub is readily easily accessible, the job can relocate rapidly; if you have to open a wall surface to eliminate the old bathtub as well as place the brand-new bathtub, the task is a lot harder. In either situation, the task is within a residence handyman's skills, although you will require a helper to vacate the old tub as well as embeded in the new one. See to it you have actually qualified yourself for the task as well as fit attempting it. As opposed to hiring a specialist to take over a halfway-completed job, it is better to consider employing one prior to you start. Chances are you might need an expert plumber to make tube connections.
This post will assist you set up a brand-new bath tub in your shower room if you have already purchased a brand-new bathtub and do not require to alter the arrangement of your previous supply of water pipes.
Your devices and material list should consist of the following:
Getting ready for the Setup
Firstly, the sustaining structure provided with the bathroom needs to be fitted (if called for) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bathtub. When fitting the tap block, it is important to ensure that if the tap features a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the faucets device to prevent stress on the tub.
Fit the adaptable faucet ports to the bottom of the two faucets utilizing 2 nuts as well as olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet via the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you utilize all of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath need to currently prepare to be suited its final placement.
Removing Old Taps
If you need to replace old faucets with new ones as a part of your setup, then the first thing you must do is separate the water system. After doing so, turn on the taps to drain any water remaining in the system. The process of eliminating the existing faucets can be fairly troublesome due to the limited gain access to that is commonly the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the taps. Have a towel all set for the remaining water that will certainly come from the pipes. When the supply pipes have actually been eliminated, use the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from turning throughout this process. Once the faucets have been eliminated, the holes in the bath/basin will need to be cleansed of any old sealing compound.
Prior to going on to fit the brand-new taps, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Mounting the Bathtub
Using the two wood boards under its feet, put the bath tub in the called for position. The wood boards are valuable in uniformly spreading the weight of the tub over the area of the boards as opposed to focusing all the weight onto 4 tiny factors.
The following goal is to make certain that the bath tub is leveled all round. This can be achieved by examining the level and also changing the feet on the tub up until the level checks out level.
To mount faucets, fit the bottom of the furthest adaptable faucet adapter to the ideal supply pipe by making a compression join; then do the very same for the various other faucet.
Activate the water system as well as inspect all joints and also brand-new pipework for leaks and tighten them if needed. Load the tub as well as also check the overflow outlet as well as the regular outlet for leakages.
Finally, fix the bathroom paneling as defined in the supplier's user's manual. Tiling and sealing around the tub needs to wait until the bath tub has been made use of at least when as this will certainly resolve it into its final position.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will need a plastic adapter to prevent damages to the thread. One end of the port fits on the plastic tail of the tap as well as the other end supplies a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly require minimizing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, place the faucet in the mounting hole in the bath/basin making certain that the washers remain in location between the tap as well as the sink. Safeguard the faucet in position with the producer offered backnut. When the faucet is firmly in place, the supply pipes can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular tap adapters. The previous kind should be linked to the faucet ends first, tightening up only by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bath satisfies the tile, it is needed to secure the joins with a silicone rubber caulking. This is important as the fitting can move enough to split a rigid seal, triggering the water to pass through the wall surface in between the bathroom as well as the tiling, leading to complications with moisture and also feasible leakages to the ceiling listed below.
You can choose from a selection of coloured sealers to blend in your components and also installations. They are marketed in tubes as well as cartridges, and can securing voids as much as a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with twists of drenched paper or soft rope. Keep in mind to constantly fill the bath tub with water prior to sealing, to permit the motion experienced when the tub remains in use. The sealant can fracture relatively very early if you do not think about this motion prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally conveniently available on the marketplace. It is suggested to fit the tiles making use of waterproof or waterproof adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were guided to that editorial on Tools You Need to Install a New Bathtub through a good friend on another domain. Sharing is caring. You never know, you may be helping someone out. Thanks for your time spent reading it.
Urgent plumbing needs? Seek professionals.